| |
|
Bronz-Glow® Product Data
SPC-Tinted
Flexible, Highly Durable Single Component Coating for Steel, Pipe, Concrete (SPC) & More
|
< Return to Products |
CORROSION PROTECTION FROM: Environments containing heavy moisture concentrations, salt air/spray, acid rain, chlorine, muriatic acid fumes, ammonia, H2S fumes, sulfuric acid fumes, methane fumes, most other aggressive acids and alkali.
COATING RECOMMENDATIONS: Corrosion protection for virtually any type of substrate material exposed to extreme corrosive environments such as those found in waste- water treatment plants, paper mills, any type of coastal installation, food processing facilities, refineries, off shore facilities, chemical plants, medical facilities, pharmaceutical plants, steel mills, mining facilities etc.
BENEFITS:
- Provides corrosion resistance across the entire pH Range (1.0 to 14.0)
Extends equipment life
- Impermeable to moisture when applied 12 to 15 dft (dry film thickness)
- Single component convenience and savings
- Applicable to virtually any type of surface
- Safe for all non-food contact surfaces
- Easy to apply by spray, dip, roll or brush application
- Bonds to metals, wood, concrete, glass, plastics, fiberglass etc.
- Contains a 10-year Florida sun UV inhibitor
DESCRIPTION: This unique air-dry coating provides durable surface protection in harsh environments where other coatings and paints fail. Dries to touch in minutes and fully cures in 24 hours. Formulated with a synthetic resin base, at 12-15 mils dry thickness SPC provides virtually total moisture resistance even from harsh alkaline and acidic solutions.
| COATING CHARACTERISTICS: |
| Solids: (wt) 28% |
Stone Abrasion: Excellent (ASTM D-3170) |
| Tensile: 2,500 psi (ASTM D-638) |
Weather ability: Excellent (ASTM G-53) 7-10 yrs |
Permeability: 03 grains / sq. ft. /hr
|
Finish: Semi-gloss |
| Temperature use range: -30 to 220° F |
Viscosity range: 85 – 95 K.V. @ 77 degrees F. |
| Shelf life: 1 year @ 77° F |
Elongation: 230% (ASTM D-2370-82) |
| VOC lbs. per gallon: 4.8 - 5.1 |
Cut Resistance: Very Good (ASTM D-1044) |
| Salt Spray 2,000 hrs (ASTM B-117.85) |
Dielectric Strength: 1.400 / mil (ASTM D-149) |
| Gas Chromatography Test (FID) No evidence of residual solvent vapors |
AVAILABLE COLORS: C-119 Light Gray, C-3 Orange, C-168 Dark Gray, C-162 Beige,
C-339 Redwood, C-196 Brown, C-444 Green
COVERAGE RATE: 150 sq. ft. per gallon @ 5 mils dft (dry film thickness) (cover rate may vary based on weather conditions)
PACKAGING:5 gallon pails, 50 gallon drums
Bronz-Glow, Husky Logo is Registered Trademark of Bronz-Glow Holdings, St. Augustine, FL.
Rust-Oleum is the registered Trademark of Rust-Oleum Corporation, Vernon Hills, and IL.
Bronz-Glow’s SPC-Tinted Technical Data
Surface Preparation:
- Remove all traces of oil, grease, rust, dirt and dust
- Sandblast or roughen surfaces to improve adhesion
- Remove all loosened residue, wipe or rinse clean
- Prime with Bronz-Glow’s Husky 150 Primer
- Rust-Oleum brand primers are not compatible.
Preparing Surfaces Exposed to High Salt Conditions
- Sandblast or wire brush metal surfaces to remove all rust and oxides
- Pressure wash with a free-rinsing, high pH cleaner
- Pressure rinse with clean water
- Pressure wash with a low pH cleaner to reduce pH to 5.0-7.0
- Allow to dry thoroughly
- Prime with Bronz-Glow’s Husky 150 Primer
Preparing Steel Surfaces
- Abrasive blast to SSPC SP-5/NACE No. 1 or Swedish Standard 3.
- Remove loosened residue
- Prime with Bronz-Glow’s Husky 150 Primer
Preparing Concrete Surfaces
- Clean, abrasive blast, or etch with 10 per cent muriatic acid
- Prime with Bronz-Glow’s Husky 150 Primer
RECOMMENDED EQUIPMENT AND SETTINGS:
Conventional and Air Assist Spray Equipment
Gun: Binks Model 2001 gun
Nozzle: 63B
Cap: 63PB or 66SD-3 for heavier build-up. (Do not dilute)
Needle: 363A
Material: 25-30 psi
Atomization: 25-40 psi
Dilution: Not required
Clean-up: Husky 15 Reducer
Airless Spray Equipment
Tip Sizes: .010-.015
Pressure: As needed
Dilution: As required
Surface Test: Painted surfaces may lift. Test a small area before applying
over
any pre-painted finish
Always provide ventilation and use approved personal safety protection when
handling or applying coatings.
For more detailed information, call, email, or visit or web site
Distributed by Bronz-Glow Technologies, Inc.
175 Bronz-Glow Way
St. Augustine, FL 32095
Ph: (904) 825-0175 or Fax: 904-825-0122
E-mail: Customerserv@bronz-glow.com or www.bronz-glow.com
Conditions of use: "The information, data contained herein, is believed to be reliable and based on our knowledge & experience; however, seller does not guarantee the result obtained by buyer. Seller herby expressly disclaims any implied warranty, of merchantability for fitness for a particular purpose and / or any other warranty expressed or implied as to any and all products and / or suggestions described herein, whether such are used alone or in conjunction with other materials. Buyer must make its own determination of suitability of any products for its use and the completeness of any information. In no event shall Bronz-Glow Technologies, Inc. Holdings Trust be liable for consequential or incidental damages"
|
