|
Bronz-Glow® Product Data
Husky 150 Primer
An Acrylic Primer for Superior Adhesion |
< Return to Products |
BENEFITS:
- Improves coating adhesion
- Extends coating life
- Aids in preventing peel back of damaged coating
- Reduces preparation time for metal surfaces
- Creates a more uniform coating
- Easy to apply by spray, dip, roll or brush application
DESCRIPTION: Increases coating adhesion on metals by up to 400 percent with this solvent base air-dry acrylic primer. It was specifically designed for use with any Bronz-Glow coating when priming is recommended. 150 Primer aids in preventing peeling on metal surfaces, including galvanized. Only extreme abrasion or corrosion requires an additional coat. Best results are achieved by applying the coating as soon as the 150 Primer is dry to touch.
| CHARACTERISTICS: |
| Solids (wt): 17% |
Range: 26 – 35 seconds w/Zahn #2 |
| VOC lbs. per gallon: 4.5 |
at 77 degrees F |
| Temperature use range: N/A |
Shelf Life: 1 yr @ 77° F |
AVAILABLE COLORS: Clear (Gray available on request)
COVERAGE RATE: 150 sq. ft. per gallon @ 1 mil dft (dry film thickness) (cover rate may vary based on weather conditions)
PACKAGING: 5 gallon pails, 55 gallon drums & 12 aerosol cans/case (clear only)
Bronz-Glow, Husky Logo is Registered Trademark of Bronz-Glow Holdings, St. Augustine, FL.
Rust-Oleum is the registered Trademark of Rust-Oleum Corporation, Vernon Hills, and IL.
Bronz-Glow’s Husky 150 Primer Technical Data
Surface Preparation:
- Remove all traces of oils, grease, rust, dirt, and dust
- Sandblast or roughen surfaces to improve adhesion
- Remove all loosened residue, wipe or rinse clean
Preparing Surfaces Exposed to High Salt Conditions
- Sandblast or wire brush metal surfaces to remove all rust and oxides
- Pressure wash with a free-rinsing, high pH cleaner
- Pressure rinse with clean water
- Pressure wash with a low pH cleaner to reduce surface pH to 5.0-7.0
- Allow to dry thoroughly before applying 150 Primer
Additional Surface Preparation
- Abrasive blast steel to SSPC SP-5/NACE No. 1 or Swedish standard Sa 3.
- Clean concrete with abrasive blast, or etch with 10 per cent muriatic acid
- Remove loosened residue
Previously Finished Surfaces
- Repair all damaged areas
- Remove gloss from previous coating
- Remove dust, corrosion products, heavy chalk, and peeling
- Spot prime bare areas
RECOMMENDED EQUIPMENT SETTINGS:
Conventional and Air Assisted Spray Equipment
Gun: Binks Model 2001 gun
Nozzle: 63B
Cap: 63PB or 66SD-3 for heavier build-up. (Do not dilute)
Needle: 363A
Material: 25-30 psi
Atomization: 25-40 psi
Dilution: Not required
Airless Spray Equipment
Tip Sizes: .010-.015
Pressure: As needed
Dilution: As required
Surface Test: Painted surfaces may lift. Test a small area before applying over
any pre-painted finish.
Always provide ventilation and use approved personal safety protection
when handling or applying coating
For more detailed information, call, email, or visit or web site
Distributed by Bronz-Glow Technologies, Inc.
175 Bronz-Glow Way
St. Augustine, FL 32095
Ph: (904) 825-0175 or Fax: 904-825-0122
E-mail: Customerserv@bronz-glow.com or www.bronz-glow.com
Conditions of use: "The information, data contained herein, is believed to be reliable and based on our knowledge & experience; however, seller does not guarantee the result obtained by buyer. Seller herby expressly disclaims any implied warranty, of merchantability for fitness for a particular purpose and / or any other warranty expressed or implied as to any and all products and / or suggestions described herein, whether such are used alone or in conjunction with other materials. Buyer must make its own determination of suitability of any products for its use and the completeness of any information. In no event shall Bronz-Glow Technologies, Inc. Holdings Trust be liable for consequential or incidental damages"
|
